收藏本站
A Product Line of
Diodes Incorporated
ZXLD1322
Application Notes
Setting Peak Coil Current
The peak current in the coil is set by the resistor (RSENSE) between the switch emitter and ground according to:
I SWPEAK
=
50mV
R SENSE
The minimum peak current will depend on operating mode, coil inductance and supply voltage range. The maximum peak
current must not exceed the specified value for the switch. (See Application circuits for details)
Setting LED Current
The nominal average LED current is given by:
I LED (NOM) =
100mV
R M
Where RM is the external resistor connected between pins M_VIN and VIN.
This current can be adjusted to a lower value by applying a dc control voltage or PWM control signal to the ADJ pin.
DC Control
The LED current can be adjusted over a 10% to 100% range by connecting a variable resistor R ADJ from the ADJ pin to
ground to vary the DC voltage at the ADJ pin. R ADJ forms the lower part of a resistive divider and the internal 100k ? resistor
between the ADJ and V REF pins forms the upper part. A value of 1M ? for R ADJ will therefore give a maximum current of
91% of I LED (nom) and the device will be turned off when the voltage on the ADJ pin falls below 28mV, corresponding to an
R ADJ value of approximately 5k ? . If required, an end-stop resistor in series with R ADJ can be used to maintain the voltage on
the ADJ pin above the turn-on threshold.
Using a logarithmic potentiometer for RADJ will give an approximately linear variation of output current with shaft rotation.
(Fig 1)
If required, the maximum output current can be restored to 100% by adjusting the value of the LED current monitor resistor
(RM). The tolerance of the internal 100k resistor and R ADJ should be taken into account when calculating output current.
The ADJ pin is clamped internally to a voltage of 575mV (nom), to limit maximum average output current to approximately
115% of I LED (nom).
Fig. 1
ZXLD1322
Document number: DS32166 Rev. 3 - 2
10 of 17
www.diodes.com
April 2010
? Diodes Incorporated
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
ZXLD1350ET5TA IC LED DRIVR WHITE BCKLGT TSOT-5
ZXLD1352ET5TA IC LED DRIVER HIGH BRIGHT TSOT-5
ZXLD1356DACTC IC LED DRIVER WHITE BCKLGT 6-DFN
ZXLD1360ET5TA IC LED DRIVR WHITE BCKLGT TSOT-5
ZXLD1362ET5TA IC LED DRIVR WHITE BCKLGT TSOT-5
ZXLD1366DACTC IC LED DRIVER WHITE BCKLGT 6-DFN
ZXLD1370EST16TC IC LED DRVR HIGH BRIGHT TSSOP-16
ZXLD1371QESTTC IC LED DRIVER
相关代理商/技术参数
ZXLD1322DCCTC-CUT TAPE 制造商:DIODES 功能描述:ZXLD1322 Series 15 V 600 kHz 700 mA Buck/Boost Mode DC-DC Converter - DFN-14
ZXLD1322DCTC 制造商:ZETEX 制造商全称:ZETEX 功能描述:Buck/boost mode DC-DC converter for LED driving with 700mA output and current control
ZXLD1350 制造商:ZETEX 制造商全称:ZETEX 功能描述:350mA LED driver with internal switch
ZXLD1350_07 制造商:ZETEX 制造商全称:ZETEX 功能描述:350mA LED driver with internal switch
ZXLD1350ET5 制造商:Diodes Incorporated 功能描述:LED DRIVER INTERNAL SWITCH SMD 制造商:Diodes Incorporated 功能描述:LED DRIVER, INTERNAL SWITCH, SMD 制造商:Diodes Incorporated 功能描述:IC, LED DRIVER, BUCK, TSOT-23-5; Topology:Buck (Step Down); No. of Outputs:1; Output Current:350mA; Output Voltage:30V; Driver Case Style:TSOT-23; Input Voltage Min:7V; Input Voltage Max:30V; Dimming Control Type:PWM / DC ;RoHS Compliant: Yes
ZXLD1350ET5TA 功能描述:LED照明驱动器 7-30V Input 350mA w/Internal Switch RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
ZXLD1350ET5TA-CUT TAPE 制造商:DIODES 功能描述:ZXLD1350 Series 350 mA 1 MHz SMT LED Driver with Internal Switch - TSOT-23-5
ZXLD1350EV3 制造商:ZETEX 制造商全称:ZETEX 功能描述:circuit diagram and bill of materials